常用塑膠真/壓空成型英文單字（英中對照）

abrasion loss磨耗
abrasion,wear磨損
accelerated ageing加速老化
accelerated test加速試驗
acid resistance耐酸性
ageing test老化試驗
air assist forming氣脹真空成形
air ejection空氣頂出
air gap空氣隙
ambient temperature環境溫度
annealing退火
artificial leather人造皮革
auxiliary cylinder輔助壓缸
back pressure valve止回閥,止逆閥
back pressure背壓
blister起泡,氣泡
blister起泡,氣泡
blooming exudation噴霜,起霜
blowing agent,expanding agent發泡劑
boiling test煮沸試驗
brightening agent,optical brightener,optical whitening agent增亮劑
buff,buffing wheel拋光布輪
buffing布輪拋光
cam凸輪
cantilever beam懸臂梁
cavity side母模
clearance間隙, 隙距
cold molding常溫成形,冷模壓
cold slug well冷料井,冷料窩
cold slug冷料
cooling channel冷卻水通路
core pin plate成孔銷托板
core pin成孔銷,模蕊銷
core side模仁,雄模,模心
core模蕊,蕊片,蕊線,蕊孔
corrosion resistance耐蝕性
cracking龜裂
crack龜裂
deflasher修邊機,修毛邊機
deflashing,definning修邊,除邊
dip coating浸漬塗裝
discharge放電
double-shot molding雙色射出成形
draft angle脫模斜度
dull surface無光面
durometer硬度計
ejection頂出,脫模
ejector pin頂出銷,頂針
ejector plate,knock-out plate頂出板
ejector頂出組合
electroformed mold電鑄模具
electroplating,electrodeposition電鍍
embossing machine壓花機
embossing壓花
environmental stress cracking test環境壓力龜裂試驗
etching蝕刻,侵蝕
fading,discoloration褪色
fatigue life疲勞壽命
fatigue strength疲勞強度
fatigue test疲勞試驗
fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP玻璃纖維強化熱塑塑膠
fiberfil molding玻璃纖維強化,熱塑塑膠射出成形
finishing修飾,塗飾,打光
flash gate,external ring gate,internal ring gate毛邊形澆口,薄膜形澆口
flash groove溢料縫,毛邊槽
flash,fin毛邊,整紋,溢料
flash溢料
flex cracking彎曲龜裂
flow mark流痕
frost line冷卻線
gate bush澆口白暈
gate澆口,灌點
glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP. 玻璃纖維強化塑膠
glass fiber,fibrous glass玻璃纖維
granule顆粒料
graphite fiber石墨纖維
graphite石墨
hand ejection手工脫模,手工頂出
hand mold,loose mold手動模具
hand press手動油壓機
hardness硬度
heating cylinder加熱管套(料筒)
heating plate加熱板
hot stamping,roll leaf stamping燙印
hydraulic intensifier油壓增壓器
hydraulic motor油壓馬達
hydraulic press油壓機
impact resistance耐衝擊性
impact strength衝擊強度
injection molding machine射出成形機
injection molding射出成形
injection mold射出成形模具
injection nozzle射出噴嘴,注料嘴
injection pressure射出壓力
injection rate射出率(量)
injection speed射出速度
injection unit射出裝置
inpact test衝擊試驗
insert pin嵌件硝
insert嵌件
jetting噴流,噴射現象
knock-out bar,ejector rod頂出杆,脫模杆
knock-out pin plate脫模銷托板,頂出銷托板
knock-out pin脫模銷,頂出銷
leader pin bushing合模銷套,導銷襯套
leader pin合模銷,導銷
light resistance,light fastness耐光性
liner內襯,襯套,襯墊
locating ring對位圈,定位環
locking force,clamping force合模力,閉模力
low pressure injection molding低壓射出成形法
lubricant潤滑劑
machine shot capacity射出容量
mirror polishing鏡面拋光
Mohs’hardness莫斯硬度
mold clamping mechanism合模機構
mold opening force開模力
mold plate範本
mold shrinkage, molding shrinkage成形收縮,模壓收縮
mold size模具尺寸
mold temperature controller模溫度控制器
mold,Tools,Tooling模具
molding cycle成形迴圈,成形週期
molding pressure成形壓力,模制壓力
molding temperature成形溫度,模制溫度
molding time成形時間,模制時間
multi-cavity mold多模穴模具
non-destructive testing非破壞性試驗
nozzle manifold支管形噴嘴
nozzle shut-off噴嘴止流
nozzle touching噴嘴接觸
nozzle噴嘴,注嘴
nylon fiber尼龍纖維
nylon尼龍,(聚醯胺樹脂之俗稱)
ozone resistance test抗臭氧試驗
ozone resistance抗臭氧性
parting line分模線
pearlescent pigment珠光顏料
peeling test剝離試驗
peeling剝離,剝皮加工
permanent elongation,tension set永久伸長
permanent set,permanent deformation永久變形
photopolymer,photo-sensitive polymer感光聚合物
pin point gate針孔形澆口
pinhole針眼,針孔
plastic deformation塑性變形
plastic fiow塑性流動
plastics foam,expanded plastics, foamed plastics,cellular plastics,plastics sponge發泡塑膠,泡沫塑料
positive mold全壓式模具
primer底漆,底膠,引發劑
prototype mold原型模,試驗模
pultrusion拉出成形
restricted gate窄澆口,限制形澆口
retainer plate托板,範本
return pin回程銷, 覆歸銷
runner流道,流道料
runner澆道,流道
sand blast噴砂,打砂
sanding砂磨
scrap grinder廢料粉碎機
scratch hardness抗刮硬度,刮痕硬度
shark skin鯊皮斑
shear gate自斷澆口,剪切澆口
shear strength剪切強度,抗剪強度
short shot充填不足,缺料
shot注射,射料
shrinkage pool縮窩,凹孔
shut-off valve止流閥
side draw pin側向模蕊(心型)銷
side gate側向澆口
silicone rubber矽橡膠
silver line銀線
sink mark,shrink mark凹痕,縮痕
sink mark凹痕,縮痕,縮水
sinter molding燒結成形法
sintering燒結法,粉鑄法
sprue bush注道襯套,澆口襯套
sprue gate注道形澆口,直接澆口
sprue注道,注道料
sprue豎澆道
stress concentration壓力集中
stress cracking壓力龜裂
stress cracking壓力龜裂
stress relaxation壓力鬆弛
stress rupture壓力斷裂,壓力破壞
stress-strain curve壓力.應變曲線
stress-strain diagram壓力.應變圖
stress壓力
stripper plate剝料板
stripper plate頂出板,脫模板
stroke行程,衝程
submarine gate沉陷式澆口,潛入式澆口
surface pin回程銷,覆歸銷
tempering回火
thermal shock test冷熱驟變試驗
thermal stress cracking,TSC熱壓力龜裂
tie-bar distance拉杆間距
tie-bar拉杆,導柱
tolerance公差,容差
torsion moment扭力矩
torsion test扭曲試驗
tunnel gate隧道形澆口
ultrasonic inserting超音(聲)波鑲嵌
ultrasonic welding超音(聲)波焊接
ultraviolet, UV紫外線
UV absorber紫外線吸收劑
UV stabilizer紫外線穩定劑
vacuum forming真空成形
void孔隙,空洞,氣泡
wall thickness肉厚
warp(ing),warpage翹曲
weatherability,weather resistance耐天侯性
weathering test天候老化試驗
weld line熔合線,結合線
welding焊接
Young’s modulus of elasticity楊氏彈性係數